Adjusting the clutch cable - Revision history

Bokonon at 21:14, 9 March 2011

2011-03-09T21:14:50Z

← Older revision		Revision as of 17:14, 9 March 2011
Line 1:		Line 1:
	[[Category:Clutch & Transmission]]		[[Category:Clutch & Transmission]]
	__TOC__		__TOC__

	====Adjustment====		====Adjustment====

Bokonon at 21:14, 9 March 2011

2011-03-09T21:14:37Z

← Older revision		Revision as of 17:14, 9 March 2011
Line 1:		Line 1:
	[[Category:Clutch & Transmission]]		[[Category:Clutch & Transmission]]
			__TOC__

	====Adjustment====		====Adjustment====

Line 35:		Line 37:
	The clutch cable tends to break more often than many people think it should, usually right here:		The clutch cable tends to break more often than many people think it should, usually right here:

	[[image:]]		[[image:Fray2w.jpg\|150px]]

	Since dealers quite often don't have these in stock, you might want to get a spare cable and zip-tie it to the current one. Should your cable break, it is just a matter of hooking up both ends and you are on your way home. That or [[Can I ride my bike home if the clutch cable breaks?\|shifting clutchless]] for the rest of your ride.		Since dealers quite often don't have these in stock, you might want to get a spare cable and zip-tie it to the current one. Should your cable break, it is just a matter of hooking up both ends and you are on your way home. That or [[Can I ride my bike home if the clutch cable breaks?\|shifting clutchless]] for the rest of your ride.

Bokonon at 21:12, 9 March 2011

2011-03-09T21:12:21Z

← Older revision		Revision as of 17:12, 9 March 2011
Line 1:		Line 1:
	[[Category:Clutch & Transmission]]		[[Category:Clutch & Transmission]]
			====Adjustment====

	The cable is adjusted by checking the amount of freeplay at the clutch lever. Free play is the amount that the lever moves before it actually starts putting any pressure on the cable.		The cable is adjusted by checking the amount of freeplay at the clutch lever. Free play is the amount that the lever moves before it actually starts putting any pressure on the cable.

Line 29:		Line 31:
	[[Image:24locktite.jpg\|170px]]		[[Image:24locktite.jpg\|170px]]

			====Cable breakage====

			The clutch cable tends to break more often than many people think it should, usually right here:

			[[image:]]

			Since dealers quite often don't have these in stock, you might want to get a spare cable and zip-tie it to the current one. Should your cable break, it is just a matter of hooking up both ends and you are on your way home. That or [[Can I ride my bike home if the clutch cable breaks?\|shifting clutchless]] for the rest of your ride.

	~~'''~~Alternative adjustment method~~'''~~		====Alternative adjustment method====

	Wes doesn't measure the free play distance, but likes it to engage when the lever is about 1 inch away from the handlebar. That way there is enough movement that the bike doesn't creep forward when the lever is pulled all the way in, but it moves when the lever is released. He does it that way to try to prevent fatigue in his clutch hand. It doesn't seem to cause excessive wear on the clutch plates.		Wes doesn't measure the free play distance, but likes it to engage when the lever is about 1 inch away from the handlebar. That way there is enough movement that the bike doesn't creep forward when the lever is pulled all the way in, but it moves when the lever is released. He does it that way to try to prevent fatigue in his clutch hand. It doesn't seem to cause excessive wear on the clutch plates.

Bokonon at 04:39, 10 May 2009

2009-05-10T04:39:55Z

← Older revision		Revision as of 00:39, 10 May 2009
Line 1:		Line 1:
	[[Category:Clutch & Transmission]]		[[Category:Clutch & Transmission]]
	The cable is adjusted by checking the amount of freeplay at the clutch lever. Free play is the amount that the lever moves before it actually starts putting any pressure on the cable.		The cable is adjusted by checking the amount of freeplay at the clutch lever. Free play is the amount that the lever moves before it actually starts putting any pressure on the cable.

	First, adjust the cable at the handlebar end so it's about in the middle of its adjustment, then use the two nuts down near the engine to set the initial free play. That way there is plenty of movement in either direction at the handlebar end for later adjustment. The lower adjusting nuts are on the right side of the engine, near the oil sight glass.

	To adjust freeplay:		To adjust freeplay:
Line 10:		Line 8:
	*Tighten the locknut.		*Tighten the locknut.

	[[Image:13adjuster2.jpg\|~~300px~~]]		[[Image:13adjuster2.jpg\|200px]]
	[[Image:adjuster-2.jpg\|~~200px~~]]		[[Image:adjuster-2.jpg\|150px]]

			[[Image:25freeplay.jpg\|170px]]

	Measure free play as so:		Measure free play as so:
Line 17:		Line 17:
	[[Image:596594.jpg\|200px]]		[[Image:596594.jpg\|200px]]

	*If your cable has stretched so much that you can't adjust it at the lever, loosen the bar ~~adjusters and~~ take some of the slack out by tightening the lower adjusting nuts.		*If your cable has stretched so much that you can't adjust it at the lever, loosen (back off) the bar adjuster all the way, then take some of the slack out by tightening the lower adjusting nuts. The lower adjusting nuts are on the right side of the engine, near the oil sight glass.

			[[Image:14aside.jpg\|150px]]

			Adjust the clutch end first. Make sure the clutch lever is pushed up, removing any play from the lever.

			[[Image:23leverpush.jpg\|170px]]

			Now adjust the cable to remove most of the free play. Make sure to tighten both locknuts.

			[[Image:24locktite.jpg\|170px]]

Bokonon at 04:25, 10 May 2009

2009-05-10T04:25:33Z

← Older revision		Revision as of 00:25, 10 May 2009
Line 1:		Line 1:
	[[Category:Clutch & Transmission]]		[[Category:Clutch & Transmission]]
	The cable is adjusted by checking the amount of freeplay at the clutch lever. First, adjust the cable at the handlebar end so it's about in the middle of its adjustment, then use the two nuts down near the engine to set the initial free play. That way there is plenty of movement in either direction at the handlebar end for later adjustment. The lower adjusting nuts are on the right side of the engine, near the oil sight glass.		The cable is adjusted by checking the amount of freeplay at the clutch lever. Free play is the amount that the lever moves before it actually starts putting any pressure on the cable.

			First, adjust the cable at the handlebar end so it's about in the middle of its adjustment, then use the two nuts down near the engine to set the initial free play. That way there is plenty of movement in either direction at the handlebar end for later adjustment. The lower adjusting nuts are on the right side of the engine, near the oil sight glass.

	To adjust freeplay:		To adjust freeplay:
Line 7:		Line 9:
	*Turn the adjuster so that the clutch lever will have the specified free play (2-3mm).		*Turn the adjuster so that the clutch lever will have the specified free play (2-3mm).
	*Tighten the locknut.		*Tighten the locknut.

			[[Image:13adjuster2.jpg\|300px]]
			[[Image:adjuster-2.jpg\|200px]]

			Measure free play as so:

			[[Image:596594.jpg\|200px]]

	*If your cable has stretched so much that you can't adjust it at the lever, loosen the bar adjusters and take some of the slack out by tightening the lower adjusting nuts.		*If your cable has stretched so much that you can't adjust it at the lever, loosen the bar adjusters and take some of the slack out by tightening the lower adjusting nuts.

	~~[[Image:596584.jpg\|200px]] [[Image:596594.jpg\|200px]]~~

	'''Alternative adjustment method'''		'''Alternative adjustment method'''

Bokonon at 00:14, 12 August 2007

2007-08-12T00:14:32Z

← Older revision		Revision as of 20:14, 11 August 2007
Line 4:		Line 4:
	To adjust freeplay:		To adjust freeplay:

	1) Loosen the locknut at the clutch lever.		*Loosen the locknut at the clutch lever.
	2) Turn the adjuster so that the clutch lever will have the specified free play (2-3mm).		*Turn the adjuster so that the clutch lever will have the specified free play (2-3mm).
	3) Tighten the locknut.		*Tighten the locknut.
	4) If your cable has stretched so much that you can't adjust it at the lever, loosen the bar adjusters and take some of the slack out by tightening the lower adjusting nuts.		*If your cable has stretched so much that you can't adjust it at the lever, loosen the bar adjusters and take some of the slack out by tightening the lower adjusting nuts.

	[[Image:596584.jpg\|200px]] [[Image:596594.jpg\|200px]]		[[Image:596584.jpg\|200px]] [[Image:596594.jpg\|200px]]
Line 13:		Line 13:
	'''Alternative adjustment method'''		'''Alternative adjustment method'''

	Wes doesn't measure the free play distance, but likes it to engage when the lever is about 1 inch away from the handlebar. That way there is enough movement that it doesn't creep when the lever is pulled all the way in, but it moves when the lever is released. He does it that way to try to prevent fatigue in his clutch hand. It doesn't seem to cause excessive wear on the clutch plates.		Wes doesn't measure the free play distance, but likes it to engage when the lever is about 1 inch away from the handlebar. That way there is enough movement that the bike doesn't creep forward when the lever is pulled all the way in, but it moves when the lever is released. He does it that way to try to prevent fatigue in his clutch hand. It doesn't seem to cause excessive wear on the clutch plates.

	The book says 2-3mm slack in the cable. Wes leaves about 15mm because he doesn't like the stock lever throw. This has the side effect of rattling like hell, though.		The book says 2-3mm slack in the cable. Wes leaves about 15mm because he doesn't like the stock lever throw. This has the side effect of rattling like hell, though.

	The key: you need SOME slack to make sure the clutch engages fully. You also need to make sure the clutch disengages fully when the lever is at the bar. You can tell if this is the case or not by listening to the pitch of the engine as you shift from neutral to 1st with the clutch in on a hot motor. It should NOT change.		The key: you need SOME slack to make sure the clutch engages fully. You also need to make sure the clutch disengages fully when the lever is at the bar. You can tell if this is the case or not by listening to the pitch of the engine as you shift from neutral to 1st with the clutch in on a hot motor. The sound should NOT change.

	As long as those two points are met, it doesn't really matter what you do. It's all personal preference.		As long as those two points are met, it doesn't really matter what you do. It's all personal preference. However, by the book is best, at least until you are familiar with your bike.

Bokonon at 22:04, 11 August 2007

2007-08-11T22:04:06Z

← Older revision		Revision as of 18:04, 11 August 2007
Line 1:		Line 1:
	[[Category:Clutch & Transmission]]		[[Category:Clutch & Transmission]]
	~~You have to adjust~~ the amount of ~~free play~~ at the lever. ~~You should~~ adjust the cable at the handlebar end so it's about in the middle of its adjustment, then use the two nuts down near the engine to set the initial free play. That way there is plenty of movement in either direction at the handlebar end for later adjustment.		The cable is adjusted by checking the amount of freeplay at the clutch lever. First, adjust the cable at the handlebar end so it's about in the middle of its adjustment, then use the two nuts down near the engine to set the initial free play. That way there is plenty of movement in either direction at the handlebar end for later adjustment. The lower adjusting nuts are on the right side of the engine, near the oil sight glass.

	To adjust freeplay: Wes doesn't measure the free play distance, but likes it to engage when the lever is about 1 inch away from the handlebar. That way there is enough movement that it doesn't creep when the lever is pulled all the way in, but it moves when the lever is released. He does it that way to try to prevent fatigue in his clutch hand. It doesn't seem to cause excessive wear on the clutch plates.		To adjust freeplay:

			1) Loosen the locknut at the clutch lever.
			2) Turn the adjuster so that the clutch lever will have the specified free play (2-3mm).
			3) Tighten the locknut.
			4) If your cable has stretched so much that you can't adjust it at the lever, loosen the bar adjusters and take some of the slack out by tightening the lower adjusting nuts.

			[[Image:596584.jpg\|200px]] [[Image:596594.jpg\|200px]]

			'''Alternative adjustment method'''

			Wes doesn't measure the free play distance, but likes it to engage when the lever is about 1 inch away from the handlebar. That way there is enough movement that it doesn't creep when the lever is pulled all the way in, but it moves when the lever is released. He does it that way to try to prevent fatigue in his clutch hand. It doesn't seem to cause excessive wear on the clutch plates.

	The book says 2-3mm slack in the cable. Wes leaves about 15mm because he doesn't like the stock lever throw. This has the side effect of rattling like hell, though.		The book says 2-3mm slack in the cable. Wes leaves about 15mm because he doesn't like the stock lever throw. This has the side effect of rattling like hell, though.

Bokonon at 09:42, 10 June 2007

2007-06-10T09:42:27Z

New page

[[Category:Clutch & Transmission]]
You have to adjust the amount of free play at the lever. You should adjust the cable at the handlebar end so it's about in the middle of its adjustment, then use the two nuts down near the engine to set the initial free play. That way there is plenty of movement in either direction at the handlebar end for later adjustment.

To adjust freeplay: Wes doesn't measure the free play distance, but likes it to engage when the lever is about 1 inch away from the handlebar. That way there is enough movement that it doesn't creep when the lever is pulled all the way in, but it moves when the lever is released. He does it that way to try to prevent fatigue in his clutch hand. It doesn't seem to cause excessive wear on the clutch plates.

The book says 2-3mm slack in the cable. Wes leaves about 15mm because he doesn't like the stock lever throw. This has the side effect of rattling like hell, though.

The key: you need SOME slack to make sure the clutch engages fully. You also need to make sure the clutch disengages fully when the lever is at the bar. You can tell if this is the case or not by listening to the pitch of the engine as you shift from neutral to 1st with the clutch in on a hot motor. It should NOT change.

As long as those two points are met, it doesn't really matter what you do. It's all personal preference.