J model oil change: Difference between revisions

Line 27:

Put a fine bead of oil on the rubber gaskets. Torque the cover to 14.5 ft/lbs.

Next step is to add oil. The '08 uses 1.7 quarts with a filter change, but you don't want to start off pouring that much in there. Fill it up 2/3 to 3/4 of the way and run the engine for 15+ seconds. Then, shut off the engine and wait several minutes for the oil to drain down. [[How do I check my oil?|Check the oil level]], and then begin adding as necessary. You may have to repeat these steps several times. Take your time and make sure you get the oil level correct. You don't want to overfill or underfill it. The oil should be at least halfway between the lower and the upper marks on the sight glass.

Next step is to add oil. The '08 uses 1.7 quarts with a filter change, but you don't want to start off pouring that much in there. Fill it up 2/3 to 3/4 of the way and run the engine for 15+ seconds. Then, shut off the engine and wait several minutes for the oil to drain down. [[How do I check my oil?|Check the oil level]], and then begin adding as necessary. You may have to repeat these steps several times. Take your time and make sure you get the oil level correct. You don't want to overfill or underfill it. The oil should be at least halfway between the lower and the upper marks on the sight glass. As these pictures were taken in the middle of an oil change, there is no oil showing in the glass.

~~'''Make sure you check~~ the oil ~~level on a flat surface~~, ~~with 250R off~~ the ~~sidestand & fully upright~~.~~'''~~

[[image:oil_change_022408_05-2.jpg|90px]]

[[image:Sight glass-6-2.jpg|150px]]

'''Make sure you check the oil level on a flat surface, with 250R off the sidestand & fully upright.'''

Run the engine for a minute or so and check for leaks. Check your oil religiously.

@@ Line 27: / Line 27: @@
 Put a fine bead of oil on the rubber gaskets. Torque the cover to 14.5 ft/lbs.
-Next step is to add oil. The '08 uses 1.7 quarts with a filter change, but you don't want to start off pouring that much in there. Fill it up 2/3 to 3/4 of the way and run the engine for 15+ seconds. Then, shut off the engine and wait several minutes for the oil to drain down. [[How do I check my oil?|Check the oil level]], and then begin adding as necessary. You may have to repeat these steps several times. Take your time and make sure you get the oil level correct. You don't want to overfill or underfill it. The oil should be at least halfway between the lower and the upper marks on the sight glass.
+Next step is to add oil. The '08 uses 1.7 quarts with a filter change, but you don't want to start off pouring that much in there. Fill it up 2/3 to 3/4 of the way and run the engine for 15+ seconds. Then, shut off the engine and wait several minutes for the oil to drain down. [[How do I check my oil?|Check the oil level]], and then begin adding as necessary. You may have to repeat these steps several times. Take your time and make sure you get the oil level correct. You don't want to overfill or underfill it. The oil should be at least halfway between the lower and the upper marks on the sight glass. As these pictures were taken in the middle of an oil change, there is no oil showing in the glass.
-'''Make sure you check the oil level on a flat surface, with 250R off the sidestand & fully upright.'''
 [[image:oil_change_022408_05-2.jpg|90px]]
 [[image:Sight glass-6-2.jpg|150px]]
+'''Make sure you check the oil level on a flat surface, with 250R off the sidestand & fully upright.'''
 Run the engine for a minute or so and check for leaks. Check your oil religiously.