Oil Change Procedure: Difference between revisions

Line 4:

Warm up the engine. Turn off the engine and let it sit for a few minutes; place the bike on centerstand. Removing the lower fairing is optional; some people prefer to do it because it's quick, gives you a bit more room in which to work, and minimizes mess; others think it's not worth the effort, so it's up to you; it's held on by 7 bolts. Remove the drain plug bolt on the bottom of the engine over a 3+ qt container (don't burn yourself). Removing the oil filler cap will help the oil drain faster. Let the oil drain for 15-20 minutes, then replace the bolt, using a new drain plug gasket, #92065. (Many people don't replace these every time, but they're cheap. Stock up.) Tighten to 14.5 lb/fts; don't overtighten it or you risk stripping the threads out of the engine case. This is difficult to fix. Remove the oil filter bolt and filter retainer, just in front of the drain bolt. More oil and a dirty filter element will come out. Be sure to keep all the springs/grommets in order.

Place the new filter (~~STP SMO-12;~~ see [[Oil Filters|oil filter page]] for options) on the retainer, and replace the assembly, again torquing the bolt to 14.5 ft/lbs. Open the filler cap on the right side of engine if you haven't already. Fill w/ 1.5 qts of your favorite oil. Wait a minute, then add a very small amount of oil at a time until oil is halfway up the level-check window. Replace the filler cap. Start up the bike and let it run for a minute, then shut off the engine and wait a few minutes before checking the window again. Put another few ounces of oil in. Repeat until oil level is consistently in the center of the view window. Centerline in the window while the bike is on centerstand is the same as full with both wheels on the ground. (The bike is tilted forward and isn't level when on the centerstand, so the level appears lower than when both wheels are on the ground.)

Place the new filter (see [[Oil Filters|oil filter page]] for options) on the retainer, and replace the assembly, again torquing the bolt to 14.5 ft/lbs. Open the filler cap on the right side of engine if you haven't already. Fill w/ 1.5 qts of your favorite oil. Wait a minute, then add a very small amount of oil at a time until oil is halfway up the level-check window. Replace the filler cap. Start up the bike and let it run for a minute, then shut off the engine and wait a few minutes before checking the window again. Put another few ounces of oil in. Repeat until oil level is consistently in the center of the view window. Centerline in the window while the bike is on centerstand is the same as full with both wheels on the ground. (The bike is tilted forward and isn't level when on the centerstand, so the level appears lower than when both wheels are on the ground.)

Do not overfill (you could blow a gasket).

Line 23:

In a new motor there will likely be less trash floating around, so it's recommended to check the screen at the second or third oil change, then every couple oil changes after that, until there's no new trash in the screen.

As far as actual cleaning of the screen goes, you can pretty much just wipe the screen clean with a rag. If you do need to spray it, WD-40 works fine.

As far as actual cleaning of the screen goes, you can pretty much just wipe the screen clean with a rag. If you do need to spray it, WD-40 works fine. There are no gaskets to worry about. Just remove, clean, and replace.

@@ Line 4: / Line 4: @@
 Warm up the engine. Turn off the engine and let it sit for a few minutes; place the bike on centerstand. Removing the lower fairing is optional; some people prefer to do it because it's quick, gives you a bit more room in which to work, and minimizes mess; others think it's not worth the effort, so it's up to you; it's held on by 7 bolts. Remove the drain plug bolt on the bottom of the engine over a 3+ qt container (don't burn yourself). Removing the oil filler cap will help the oil drain faster. Let the oil drain for 15-20 minutes, then replace the bolt, using a new drain plug gasket, #92065. (Many people don't replace these every time, but they're cheap. Stock up.) Tighten to 14.5 lb/fts; don't overtighten it or you risk stripping the threads out of the engine case. This is difficult to fix. Remove the oil filter bolt and filter retainer, just in front of the drain bolt. More oil and a dirty filter element will come out. Be sure to keep all the springs/grommets in order.
-Place the new filter (STP SMO-12; see [[Oil Filters|oil filter page]] for options) on the retainer, and replace the assembly, again torquing the bolt to 14.5 ft/lbs. Open the filler cap on the right side of engine if you haven't already. Fill w/ 1.5 qts of your favorite oil. Wait a minute, then add a very small amount of oil at a time until oil is halfway up the level-check window. Replace the filler cap. Start up the bike and let it run for a minute, then shut off the engine and wait a few minutes before checking the window again. Put another few ounces of oil in. Repeat until oil level is consistently in the center of the view window. Centerline in the window while the bike is on centerstand is the same as full with both wheels on the ground. (The bike is tilted forward and isn't level when on the centerstand, so the level appears lower than when both wheels are on the ground.)
+Place the new filter (see [[Oil Filters|oil filter page]] for options) on the retainer, and replace the assembly, again torquing the bolt to 14.5 ft/lbs. Open the filler cap on the right side of engine if you haven't already. Fill w/ 1.5 qts of your favorite oil. Wait a minute, then add a very small amount of oil at a time until oil is halfway up the level-check window. Replace the filler cap. Start up the bike and let it run for a minute, then shut off the engine and wait a few minutes before checking the window again. Put another few ounces of oil in. Repeat until oil level is consistently in the center of the view window. Centerline in the window while the bike is on centerstand is the same as full with both wheels on the ground. (The bike is tilted forward and isn't level when on the centerstand, so the level appears lower than when both wheels are on the ground.)
 Do not overfill (you could blow a gasket).
@@ Line 23: / Line 23: @@
 In a new motor there will likely be less trash floating around, so it's recommended to check the screen at the second or third oil change, then every couple oil changes after that, until there's no new trash in the screen.
-As far as actual cleaning of the screen goes, you can pretty much just wipe the screen clean with a rag. If you do need to spray it, WD-40 works fine.
+As far as actual cleaning of the screen goes, you can pretty much just wipe the screen clean with a rag. If you do need to spray it, WD-40 works fine. There are no gaskets to worry about. Just remove, clean, and replace.