Mounting & balancing tires yourself: Difference between revisions

Line 103:

[[Image:mount balance 14.JPG|150px]]

Then push the ~~top~~ bead into the center of the rim, put some lube on the bead that is still outside the rim, and slowly work the tire on with your irons... It is important that you put the bead that is already all the way on the rim into the center of the rim (the deepest part), and not against the side of the rim on the far side. This will give your tire more slack, and will make it less likely that you'll have to bust your fingers trying to get the second bead on.

Then push the first bead into the center of the rim, put some lube on the bead that is still outside the rim, and slowly work the tire on with your irons... It is important that you put the bead that is already all the way on the rim into the center of the rim (the deepest part), and not against the side of the rim on the far side. This will give your tire more slack, and will make it less likely that you'll have to bust your fingers trying to get the second bead on.

There are no pictures of this process, as it's impossible to stop without having the tire work its way off the rim. Here's Leon to give you a good idea of how it works. Keep your knees on the part that's already on the rim, the first bead in the low center part of the rim, work your way around with your tire irons, and it should only be difficult the last little bit.

Line 115:

One tip, if the above methods don't work, is to use a ratcheting tiedown wrapped all the way around the tire and compress the tire down into the rim (this will force the beads towards the lips). Then you can seat the beads with air, as usual.

You'll then want to look for an even ring all the way around the rim, on the tire (there's usually some rings molded into the tire to make this task simple). If it's not even all the way around, the bead is not fully seated. Now, put the core back in the valve stem and fill the tire up. I usually go over what I normally run until I get it back on the bike. Always easier to let some out than to add some back.

====Balancing====

@@ Line 103: / Line 103: @@
 [[Image:mount balance 14.JPG|150px]]
-Then push the top bead into the center of the rim, put some lube on the bead that is still outside the rim, and slowly work the tire on with your irons... It is important that you put the bead that is already all the way on the rim into the center of the rim (the deepest part), and not against the side of the rim on the far side. This will give your tire more slack, and will make it less likely that you'll have to bust your fingers trying to get the second bead on.
+Then push the first bead into the center of the rim, put some lube on the bead that is still outside the rim, and slowly work the tire on with your irons... It is important that you put the bead that is already all the way on the rim into the center of the rim (the deepest part), and not against the side of the rim on the far side. This will give your tire more slack, and will make it less likely that you'll have to bust your fingers trying to get the second bead on.
 There are no pictures of this process, as it's impossible to stop without having the tire work its way off the rim. Here's Leon to give you a good idea of how it works. Keep your knees on the part that's already on the rim, the first bead in the low center part of the rim, work your way around with your tire irons, and it should only be difficult the last little bit.
@@ Line 115: / Line 115: @@
 One tip, if the above methods don't work, is to use a ratcheting tiedown wrapped all the way around the tire and compress the tire down into the rim (this will force the beads towards the lips). Then you can seat the beads with air, as usual.
 You'll then want to look for an even ring all the way around the rim, on the tire (there's usually some rings molded into the tire to make this task simple). If it's not even all the way around, the bead is not fully seated. Now, put the core back in the valve stem and fill the tire up. I usually go over what I normally run until I get it back on the bike. Always easier to let some out than to add some back.
 ====Balancing====